|
The
main HF antenna is a 42m multi-band Doublet antenna fed with open wire
ladder-line and enters the radio room with a sort length of coax run
through the roof and building wall to a T-Match tuner. The
un-balanced coaxial cable is connected to the balanced feed line
with the combination of a 1:1 choking balun and a 1:4 impedance step up
balun connected in series.
The antenna, feed lines, balun and antenna set-up is shown in below in
Fig 1.
The
1:1 choking balun is to mitigate common mode RF currents on the coax
cable, reduces noise pickup on the coax from within the building
entering the antenna system and also produce a balanced antenna system
that will have a more predictable radiation pattern .
The 1:4 impedance step up balun is
included to more broadly match the range of impedance at the
antenna/feed line with the nominal 50-ohm impedance of the coax.
Figure
1 Multi-band Doublet, feed-lines and balun configuration
Basic Multi-band
Doublet Arrangement
(1)
Inverted 'V' Dipole. (42Mtr total length)
(2)
450 Ohm Ladder Line. (7.5Mtr)
(3)
1:4 Current Balun. See Balun Guanella Current 1:4 Single core
(4)
1:1 Choking Balun. See Balun Choke HF
(5)
LDF4-50 Heliax
(3.5Mtr)
(6)
T-Match Tuner. See T Match Tuner
(7)
VSWR Meter.
(8)
HF Transceiver.
Construction
The
1:1 choking balun is a length of RG58 50ohm coax wound with 14 turns
on a single FT240-43
ferrite toroid core. See
Fig 2 for the connection details and Balun Choke HF
for the
1:1 choking balun details.
The
1:4 current balun has two ideally 100ohm transmission lines
wound evenly spaced in the same direction around a single FT240-43
ferrite toroid core. See
Fig 2 for the connection details and Balun Guanella Current 1:4 Single core
for balun details.
Figure
2 Detail Balun configuration
Photo
1 Balun housing for coax to ladder line interface.
Photo
2 Balun assembly.
Testing
The AIM 4170C antenna analyser recorded the balun impedance
transformation efficiency and common mode choking for a frequency
range from less than 100kHz to 30MHz.
Figure
3 AIM
4170C antenna analyser
plot viewing a 200ohm resistive load through the feed-line
balun. Note the 200ohm resistor appears as
50ohms due to the 1:4 balun ratio resulting in an ideal SWR of 1:1. This
plot shows an SWR of no greater than 1.7:1 with from 100kHz to 30MHz.
Figure
4 AIM
4170C antenna analyser
plot viewing a 200ohm resistive load through the feed-line
balun. Note the 200ohm resistor appears as
50ohms due to the 1:4 balun ratio. This plot shows an 50 ~ 60
ohms from 100kHz to 30MHz.
Figure
5 The evaluation of the choking impedance of the balun over a bandwidth
from 0.5MHz- 30MHz.
Figure
6 Choking impedance to dB of choking. 20dB attenuation should be considered the minimum.
Also
see other baluns and ununs:
BALUN
1:1 CHOKE & 1:4 BALUN HF
ladder feed-line to coaxial cable combination choke and 1:4 balun.
(0.1MHz - 30MHz).
BALUN
1:1 CHOKING Choking balun
for lower HF and MF bands. (200kHz - 10MHz).
CHOKING
1:1 BALUN - HF BANDS Reisert
choking balun.
(1.0MHz - 30MHz). FT240-43 Ferrite Toroid Core.
CHOKING
1:1 BALUN - HF BANDS Reisert
choking balun
(1.5MHz - 30MHz). FT140-43 Ferrite Toroid Core.
CHOKING
1:1 BALUN - LOW VHF BAND Choking balun.
(10MHz - 60MHz). FT140-43 Ferrite Toroid Core.
BALUN
1:1 CURRENT 1:1
Guanella
Current
balun
using a L15 ferrite core (1.8 - 30MHz).
BALUN
1:4 CURRENT 1:4
Guanella
Current
balun
using a L15 ferrite core (1.8 - 30MHz).
BALUN
1:4 SINGLE CORE CURRENT 1:4 Guanella
Current Balun, single FT240-43
ferrite toroid cores.
(0.3MHz - 30MHz).
BALUN
1:1 VOLTAGE 1:1 Ruthroff
voltage balun using a T-200-2
powdered iron toroid core (1.8 -
30MHz).
BALUN
4:1 VOLTAGE 4:1 Ruthroff
voltage balun using a T-200-2
powdered iron toroid core (1.8 -
30MHz).
BALUN
6:1 VOLTAGE - VERSION 1 6:1
Voltage balun using a L15
ferrite toroid core (1.8 - 30MHz).
BALUN
6:1 VOLTAGE - VERSION 2 6:1
Voltage balun using a FT140-43
Ferrite Toroid Core (1.8 - 30MHz)
BALUN
9:1 VOLTAGE - VERSION 1 9:1
Voltage balun using a L15
ferrite toroid core (1.8 - 30MHz).
BALUN
9:1 VOLTAGE - VERSION 2 9:1
Voltage balun using a FT140-43
Ferrite Toroid Core (0.5 - 60MHz).
UNUN
9:1 VOLTAGE 9:1 voltage unun
using a
T-200-2 powdered iron toroid
core
(1.8 -
30MHz).
UNUN
9:1 VOLTAGE VERSION 2 9:1 voltage unun
using a L15 ferrite core (1.8 -
30MHz).
UNUN
9:1 VOLTAGE VERSION 3 9:1 voltage unun
using a FT140-43 ferrite core (0.5 -
60MHz).
|
